中文

hnbr fuel tube temperature rating

Viton fuel tubing - FlyingGiants

7/11/2009· Originally Posted by zzw26n. item # 5119K41. High-Temp Viton® Fluoroelastomer Tubing Soft, 1/8" ID, 1/4" OD, 1/16" Wall, BlackIn stock. Quantity Per Ft. 1-49 Ft. $3.61. 50 or more $2.89. That''s definitely the correct part nuer and dimensions for our appliion. Hardness - Unlike Tygon, Viton comes in different "Durometer", or hardness, ratings.

Materials Chemical Compatibility Guide

temperature of HNBR ranges between -30 °C/-22 °F and +140 °C/+284 °F (for a short period of time up to +160 °C/+320 °F) in contact with mineral oils and greases.

Rubber Material Selection Guide NBR / Nitrile or Buna N

Low Temperature Range - 70º F to 0º F Minimum for Continuous Use (Static) - 40º F Brittle Point - 70° F to 0º F High Temperature Range + 210° F to + 250º F Maximum for Continuous Use (Static) + 250º F ♦ Environmental Performance Colorability Excellent Flame Resistance Poor Gas Permeability Fair to Excellent Odor Good

ProPress®G 21033 | Kenny Pipe

ProPress®G 21033 Sealing Element, For Use With Viega ProPress CTS Fitting, 1 in, HNBR, Yellow, Import. The Viega ProPressG™ system is designed and engineered for use with a variety of appliions, including natural gas, LP gas and fuel oil appliions. You can identify a genuine Viega ProPressG™ fitting by the yellow dot which signifies

Section VII – Compatibility Tables for Gases, Fluids, Solids

NOTE: *These temperature ranges will apply to the majority of media for which the material is potentially recommended. With some media however, the service temperature range may be signifi cantly different. ALWAYS TEST UNDER ACTUAL SERVICE CONDITIONS. Compatibility Tables for Gases, Fluids, Solids COMPOUND COMPATIBILITY RATING 1 - Satisfactory

Polyurethane Tubing Series TU/TIUB - SMC Pneumatics

at a temperature of 20°C. Refer to the burst pressure characteristics curve for other temperatures. Furthermore, abnormal temperature rises caused by adiabatic compression may result in the burst of the tube. 3. The value of the minimum bending radius is measured at the temperature of 20°C as shown in the figure below. Black (B) White (W) Red (R)

Elastomer Temperature Chart - Resources - Rubber Fab

Gasket Material. Temperature Range. Tuf-Flex®/Ansi-Flex. -20ºF to 300ºF (-29ºC to 149ºC) Tuf-Steel®. -320ºF to 550ºF (-195ºC to 288ºC) Kalrez®. -4ºF to 428ºF (-20ºC to 220ºC) GYLON BIO-PRO®.

HNBR O-ring | O-Ring ERIKS

The HNBR O-ring has a temperature range from -30°C to +150°C (-20°F to +302°F). HNBR O-ring has excellent resistance to oils and chemicals Obtained by hydrogenating the nitrile copolymer, the HNBR O-ring fills the gap left between NBR, EPDM and FKM elastomers where high temperature conditions require high tensile strength while maintaining excellent resistance to oils and chemicals.

HNBR O-Ring Manufacturer

The advantage of HNBR seals lies in its resilience, and its ability to retain its physical and mechanical properties over its service life. Service temperature for HNBR seals typically range from -40 degrees Celsius to 150 degrees Celsius, and minimal degradation is observed over extended periods in service. Visit site for more information..

ZoomLock - Parker Hannifin Corporation

TUBE DEPTH CHECK TUBE DEPTH CHECK FOR “RLS” MARK AFTER CRIMP CHECK CRIMP WITH CRIMP GAUGE O-Ring Temperature Rating:-40°F to +300°F -40°C to +149°C HNBR Fitting Warranty

Temperature - OringsUSA

The temperature range is determined by the base elastomer used. This chart depicts the maximum temperature range for each elastomer. The temperature range for a specific compound may not reach these maximum limits. Higher temperatures may be considered if exposure is short or intermittent. Material Low end Operating Temperature High endOperatingTemperature Aflas® 25°F 450°F Butyl […]

O-Rings for Oil and Gas Industry Selection Guide

The temperature ranges presented above are approximations for dry air service only and should not be used to determine design specifiions or end-use temperature limits. Actual temperature range of a compound in an end-use appliion is highly dependent on part type, hardware configuration, applied forces, chemical media, pressure and thermal cycling effects, and other factors.

HNBR O-rings - GTeek

Service Temperature of HNBR O-rings: For HNBR the Service Temperature is from -40 C to 150 C and some special compounds can handle up to 160 C. Hardness of HNBR O-rings: 55 to 90 Shore A are available. Color of HNBR O-rings: Black, green, blue, brown, rust and gray are available, or any Color we can design for you. Appliion of the HNBR O-rings:

O-rings HNBR - 70 Shore A

The HNBR O-ring has a temperature range of -30°C to +150°C. HNBR O-rings are excellently resistant to oils and chemicals. Obtained by the hydrogenation of the nitrile copolymer, the HNBR O-ring fills the void left between the NBR, EPDM and FKM elastomers where high-temperature pressures demand high tensile strength while retaining excellent tolerance to oils, freon and chemicals.

Choosing The Right Seat Material is the Most Challenging

Offers the abrasion resistance of metal with higher pressure and temperature ratings than RPTFE. Temperature rating -20°F to 550°F / Steam rating 250 SWP Gray T TFE Tefl on is excellent at pressures below 1500 psi & at temperatures from -20°F to 400°F. It will not withstand temperature fl uctuations in excess of 200°F & are not

O-Ring and Rubber Seal Materials: NBR, FKM, EPDM | Pegasus

27/4/2020· This makes it a good choice for seals in fuel systems running pure gasoline (no ethanol blends) or diesel (not biodiesel). NBR is also fully compatible with water and ethylene glycol coolants. On the other hand, NBR has a relatively low maximum operating temperature at 212F (250F can be tolerated in fully static seals, but seal life will diminish).

Type Approval Certifie

RATINGS ERV- GS and ERV-GS HNBR Yellow Steel MAWP : 16 bar at max. service temperature of 60°C, DN 25 to DN 400 MAWP : 10 bar at max. service temperature of 100°C (NBR short time) and 120°C (HNBR short time), DN 25 to DN 600 Restrictions for oil fuel, lubriion oil and other flammable liquids

A Guide to High-Temperature Resistant Rubber Materials

24/6/2020· HNBR is an exceptionally high-temperature-resistant rubber that can withstand much higher temperatures than conventional nitrile up to +150 °C. HNBR also offers excellent resistance to oils, fuels, many chemicals, steam and ozone, as well as exceptional tensile and tear strength. It also offers good abrasion resistance.

Flange Table ASME PN AS2129 4331 4087 ISO700501 BS10EFH

Pressure-Temperature Ratings. Pressure/temperature ratings are maximum allowable working pressures allowed as per ASME B16.5 (published in metric and imperial). For intermediate temperatures, linear interpolation is calculated by manufacturers. Pressure-temperature ratings apply to flanged joints which may be reduced by gaskets or studs used.

Viega ProPress Systems

tube in accordance with ASTM B88 or B75. When pressing onto B88 copper tube, types K, L, and M may be used. Tempers O60 and O50, known as “soft copper”, are limited to nominal sizes ½" to 1¼". Temper H58, known as “hard copper”, may be used with nominal sizes ½" to 4". When pressing onto B75 copper tube, additional considerations apply.

O-Ring Material Selection Chart Interactive Comparison Guide

The temperature ranges presented above are approximations for dry air service only and should not be used to determine design specifiions or end-use temperature limits. Actual temperature range of a compound in an end-use appliion is highly dependent on part type, hardware configuration, applied forces, chemical media, pressure and thermal cycling effects, and other factors.

HNBR / X-NBR | O-Ring

HNBR is resistant to mineral oil-based hydraulic fluids, animal and vegetable fats, diesel fuel, ozone, sour gas, dilute acids and bases. HNBR also resists new bio-oils (biological oils). HNBR is suitable for high dynamic loads and has a good abrasion resistance. HNBR is suitable for temperatures from -30°C to +150°C (-20°F to +302°F).

Appliions - Valve Seat Seal Materials

Temperature rating -50ºC to 100ºC. NYLON/DEVLON - Nylon (polyamide) seats are offered for higher pressure and lower temperature service. They can be used in high temperature air, oil and other gas media but are not suited for strong oxidizing. Not recommended for water. Temperature rating …

Rubber Material Reference, Neoprene, EPDM, Buna-N

HNBR : Hydrogenated Acrylonitrile-butadiene rubber-22 F / 300 F : Excellent heat and oil resistance, improved fuel and ozone resistance (approximately 5X) over Nitrile Good abrasion resistance. Decreased elasticity at low temperatures with hydrogenation over standard nitrile.

High Pressure Nylon Tubing | Nylon 11 Tubing

It is also a high temperature tubing, made for temperatures up to 200°F (93°C). The material is ideal for chemical and oil processing lines, tool lubriing systems, pneumatics and other appliions that require high quality tubing with much higher burst ratings than typical nylon tube can provide.

Viton / FKM vs Nitrile: Which material is right for your

Temperature range:-35°C and +110°C (+135°C intermittent)-25°C to +205°C (+230°C intermittent) Suited for: General purpose sealing, such as petroleum oils, water and some hydraulic fluids. NBR is also resistant against tears and abrasive treatment.

Copyright © 2020 Setone Hydraulics CO..LTD, All rights reserved.sitemap